Dung dịch keo tăng độ kết dính 3M Primer 94 946.3ml (Trắng)

1,259,000₫
Thương hiệu Khác
Mã sản phẩm 021200239298
Mua ngay

Dung dịch keo tăng độ kết dính 3M Primer 94 946.3ml (Trắng)


Được dùng để thúc đẩy (nâng cao) độ kết dính của băng keo 3M, hay silicone, bề mặt dính keo khác lên các bề mặt polyethylene, polypropylene, ABS, PET/PBT blends, concrete, wood, glass, metal and painted metal surfaces. 
Trước hết bề mặt cần được chuẩn bị thật sạch và khô ráo, sau đó dùng tăm bông hay cọ nhỏ quét 3M Primer 94 lên trên trước khi dán hay quét vào chỗ đã dán - mép dán silicone, keo lên bề mặt để đạt hiệu quả dính nhanh nhất:

3M Tape Primer 94 can be used to promote adhesion of 3M tapes to surfaces such polyethylene, polypropylene, ABS, PET/PBT blends, concrete, wood, glass, metal and painted metal surfaces. Surface Preparation: 
The bonding surface must be relatively clean and dry. 
Contaminated surfaces should be cleaned with a 50/50 Isopropyl Alcohol and water mixture. 
A clean lint-free cloth should be used. Application: Shake 3M primer 94 well before using. 
Apply a thin uniform coating to the bonding surface using the minimum amount that will fully coat the surface. 
Allow 3M primer 94 to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature. Be sure the primed surface remains free from contaminants prior to applying the tape. Porous surfaces may require 2 applications of 3M primer 94 for uniform coverage and good adhesion.
 Allow first application of primer to dry before applying the second coat. 

3M primer 94 may be applied with brush or swab. 
It can also be applied with a pressurized flow gun, knurled roller or other similar type of application equipment. 
Clean up: 3M primer 94 can be removed with isopropyl alcohol. 
Vigorous scrubbing may be required. IFrame
Tài liệu kỹ thuật - Datasheet

Dung dịch keo tăng độ kết dính 3M Primer 94 946.3ml (Trắng)

IFrame
IFrame
Tham khảo: 
link: http://www.mazdasnw.com/showthread.php?8353-how-to-wrap-your-parts-with-carbon-fiber-vinyl-tutorial-Wu!-Wraps

3m di-noc 3m 1080 oracal 970ra etc...

sup sup,

so i thought i'd share some of my tips/techniques with all you guys n everyone online that is interested! 

this is a bmw e46 coupe interior trim out of a 2001 bmw m3 hardtop. 


this is the tools you need: 
heat gun, rubbing alcohol, squeegie, a 1/4 part of a squeegie(for smaller corners), exacto blade/hobby knife, some sort of pin popper/needle, large scissors, small sharp point scissors, small paint brush(for 3m primer #94), a shammy, and 3m primer #94(mainly for 3m di-noc, you can use it around edges/groves/ares that have dips in them. just remember once you lay the vinyl down on a area that has the 3m primer #94 on it is best if you do not lift it back up/reposition it.)



wrapping the front of your part is pretty straight forward, once you have found your corners, flip it over and start to make relief cuts around the corners of the backside. make sure your cuts don't go toooo close to the edges since sometimes you might cut tooo close and yes, you will see little spots where the material is short on the front side. once your done, it should look something like this. 




flip it over and your piece should look something like this.


now use some primer #94 around the edges of the back, don't drench it, it does not need to be. 


now heat up the primer #94 so it dries out, you will see it looks a bit tacky, the key here is to make sure it is dry, not still runny. use your brush to brush off any excess primer #94 that might be to heavy. 



now heat up your little triangular flaps to make them nice and flat/smooth. the key here is to make sure the vinyl is somewhat warm/soft PRIOR to you just folding them down! i usually go in sections, don't try to heat up the whole thing and just fold all the pieces back at once, the vinyl doesn't stay warm/soft that long and you might not get a nice and smooth fold over the backside if you do this. this is the MAIN step that makes your work a 10 vs. sup par. 


bmw e46 interior trim 3m di-noc ca-418 carbon fiber Wu! Wraps 6



some other examples on a more curvy part
bmw e46 interior trim 3m di-noc ca-418 carbon fiber Wu! Wraps 4
bmw e46 interior trim 3m di-noc ca-418 carbon fiber Wu! Wraps 3
bmw e46 interior trim 3m di-noc ca-418 carbon fiber Wu! Wraps 2

and the final results
bmw e46 interior trim 3m di-noc ca-418 carbon fiber Wu! Wraps 1

sup sup, did this one this morning waiting for my 10am audi job. took like 30min. bmw 1-series steering wheel trim. pretty common for the rubberized finish to peel/chip off on the newer bmw's. dunno why they decided to use this type of material... as you can see once wrapped you can't even tell it was messed up. came out great! this is a out of town job, will be mailing this back & receiving the rest of the interior trim shortly. Wu! Wraps

tools needed:


1 wipe down with rubbing alcohol 

2 cut your material
Mua ngay